| | Oil smoke problem |  |
|
|
| Author | Message |
|---|
tomo
Posts : 175
Join date : 2012-09-04
Age : 34
Location : whitby
| | Subject: Oil smoke problem Wed 11 Jun - 16:14 | |
| Now then people got a problem
Developed a mis fire on cyclinder 4 so for a coil from subatu snd it cured it but noticed putting a little bit of oil out of the exhaust so took turbo off and seals had gone so got jonny to rebuild it and wen i got it back cleaned the boost pipes and swilled the intercooler out as a bit of oil were in it, any way put it all back together and when driving fine but when slowing down and setting back off it smokes oily smoke out of the exhaust and i cnt think of what could be causing it if too much pressure build up or how to cure it any help would be very helpfull cheers | |
|
| | |
Marshffs
Posts : 3332
Join date : 2012-02-19
Age : 38
Location : Crook, county durham
| | Subject: Re: Oil smoke problem Wed 11 Jun - 16:57 | |
| What colour is the smoke?
Could be residue oil left in intercooler but worst case is the piston rings mate.
Get someone to have a good look. | |
|
| | |
tomo
Posts : 175
Join date : 2012-09-04
Age : 34
Location : whitby
| | Subject: Re: Oil smoke problem Wed 11 Jun - 17:02 | |
| how would you find out if rings? is it a strip down? | |
|
| | |
Marshffs
Posts : 3332
Join date : 2012-02-19
Age : 38
Location : Crook, county durham
| | Subject: Re: Oil smoke problem Wed 11 Jun - 17:04 | |
| Pressure test mate. That will be worse case scenario mate. Is it using oil? Loss of power? Drinking more fuel than normal?
| |
|
| | |
tomo
Posts : 175
Join date : 2012-09-04
Age : 34
Location : whitby
| | Subject: Re: Oil smoke problem Wed 11 Jun - 17:12 | |
| Its dropped from 1.5 to 0.5 i put that down to it running smokey like limp mode and havnt really drove it enough to see about fuel will hav to get it pressure checked and hopefully it isnt that lol | |
|
| | |
Marshffs
Posts : 3332
Join date : 2012-02-19
Age : 38
Location : Crook, county durham
| | Subject: Re: Oil smoke problem Wed 11 Jun - 17:29 | |
| A litre is a lot mate. They use oil but nowhere near that. Hope it aint the rings bud and hope you sort it. | |
|
| | |
tomo
Posts : 175
Join date : 2012-09-04
Age : 34
Location : whitby
| | Subject: Re: Oil smoke problem Wed 11 Jun - 17:30 | |
| no bar boost pressure lol | |
|
| | |
Marshffs
Posts : 3332
Join date : 2012-02-19
Age : 38
Location : Crook, county durham
| | Subject: Re: Oil smoke problem Wed 11 Jun - 17:30 | |
| Ahhhh lol. Thought you ment oil | |
|
| | |
tomo
Posts : 175
Join date : 2012-09-04
Age : 34
Location : whitby
| | Subject: Re: Oil smoke problem Wed 11 Jun - 17:31 | |
| no gonna get it plugged in and get a pressure check | |
|
| | |
Marshffs
Posts : 3332
Join date : 2012-02-19
Age : 38
Location : Crook, county durham
| | Subject: Re: Oil smoke problem Wed 11 Jun - 17:33 | |
| | |
|
| | |
tomo
Posts : 175
Join date : 2012-09-04
Age : 34
Location : whitby
| | Subject: Re: Oil smoke problem Wed 11 Jun - 17:33 | |
| a garage i no near whitby | |
|
| | |
Marshffs
Posts : 3332
Join date : 2012-02-19
Age : 38
Location : Crook, county durham
| | Subject: Re: Oil smoke problem Wed 11 Jun - 17:34 | |
| Let us know the outcome lol | |
|
| | |
Jonny Gav
Admin
Posts : 6837
Join date : 2010-03-12
Age : 53
Location : Durham
| | Subject: Re: Oil smoke problem Wed 11 Jun - 18:55 | |
| If they don't get to the bottom of it I would take it to mr kindon, it will save you a lot of money in the long run.
When I stripped your turbo I found some scaring on the rear of the shaft around the seal and bearing area, the rear bearing had some wear in it and it also had burnt on oil on the center of the shaft, I managed to remove it and polished out most of the scaring, changed the rear bearing and replaced the front and rear seals.
The area around the seal wasn't perfect but I would have expected it to seal ok.
If it hasn't sealed I would recommend a replacement core for it.
| |
|
| | |
tomo
Posts : 175
Join date : 2012-09-04
Age : 34
Location : whitby
| | Subject: Re: Oil smoke problem Wed 11 Jun - 20:44 | |
| how much wud it be for a new core? | |
|
| | |
andyden71
Posts : 2854
Join date : 2010-11-11
Age : 52
Location : Bishop Auckland
| | Subject: Re: Oil smoke problem Wed 11 Jun - 20:50 | |
| I had that on a old car it was the valve seals | |
|
| | |
Sponsored content
| | Subject: Re: Oil smoke problem | |
| |
|
| | |
| | Oil smoke problem | |
|
Calendar